IKARUS Forums  

Go Back   IKARUS Forums > IKARUS English > ECO - Piccolo

ECO - Piccolo Discuss all ECO - Piccolo related things right here.

Reply
 
Thread Tools Display Modes
  #1  
Old 21.05.02, 22:06
Petermcc Petermcc is offline
Senior Member
 
Join Date: Jun 2001
Location: Northamton UK
Posts: 622
Default Ikarus CP and K&S Pitch gauge

Ok I give in! Can someone tell me how to use my K&S pitch gauge with my Piccolo CP? The instructions are pretty much in Chinese and I think I can work it out as follows:

1. zero throttle / collective on the tx

2. align flybar, paddles, links & blades until they are ALL horizontal. Might need to adjust the screws on the CP head to get here. This gives zero pitch?

3. Adjust Pitch %age on my JR XP652 until I get +4 degrees mid throttle (or until it starts to lift when I hold it with 75% throttle curve dialled in)

4. Get about 8-10 degrees at full throttle.

I'm lining up the top of the pitch gauge, by sight, with the top of the flybar. Is this correct? My Picc barely lifts off the ground and everything else was fine before the cp conversion... [img]images/icons/confused.gif[/img]

[ 21 May 2002, 22:07: Message edited by: Petermcc ]
Reply With Quote
  #2  
Old 21.05.02, 22:17
Ecoflyer
Guest
 
Posts: n/a
Default Re: Ikarus CP and K&S Pitch gauge

Hey there,

First of all, you need at least an 8 cell nicad or a 9 cell nimh. The forget the pich gauge, you need as much pitch as you can get on this little heli. Use the larger of the pinions, which is the 10 tooth and you should be set from there. I don't think that 4 degrees pitch will lift the heli.
Reply With Quote
  #3  
Old 21.05.02, 22:21
Petermcc Petermcc is offline
Senior Member
 
Join Date: Jun 2001
Location: Northamton UK
Posts: 622
Default Re: Ikarus CP and K&S Pitch gauge

Hi - I'm using the 10 tooth pinion, an 8-cell NiCad (at least 550mah as I recall) and have tried it with a higher pitch than 4 degrees to no avail!
Reply With Quote
  #4  
Old 21.05.02, 23:50
born2net
Guest
 
Posts: n/a
Default Re: Ikarus CP and K&S Pitch gauge

Petermcc,
Do you have a picture or a link to a picture of the pitch gauge ?

Regards,

Sean - HeliHobby.com
Reply With Quote
  #5  
Old 23.05.02, 00:36
Petermcc Petermcc is offline
Senior Member
 
Join Date: Jun 2001
Location: Northamton UK
Posts: 622
Default Re: Ikarus CP and K&S Pitch gauge

Hi -I took a pic of the gauge but not sure how I embed it in this reply! I can email it to you (120kb)!
Reply With Quote
  #6  
Old 22.05.02, 14:20
pgoelz pgoelz is offline
Senior Member
 
Join Date: Feb 2000
Location: Rochester Hills, Michigan USA
Posts: 6,370
Default Re: Ikarus CP and K&S Pitch gauge

I do no tthink that 4 degrees is anywhere near enough pitch. I think that even my Raptor hovers at about 5-6 degrees, and the CP Piccolo on stock CP blades hovers at more than that.

As ECOFLYER said, don't worry about a pitch guage. Set the servo and linkages so that at full positive collective the pitch slider just contacts the bottom of the hub and at full negative collective you have SOME negative pitch (as much as you have positive if you plan on aerobatics). Then set the throttle curve so that you have your target head speed at all collective settings and you're done. This is so much easier with the Piccolo because you can do the throttle curve while running it in your hand.

At full positive collective I have quite a bit more pitch than the 15 degrees that is the limit of my pitch guage.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +2. The time now is 12:31.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd.